home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Network Supervisor's Toolkit
/
Network Supervisor's Toolkit.iso
/
novell
/
fyi8
/
080122.dos
< prev
next >
Wrap
Text File
|
1996-07-10
|
6KB
|
110 lines
Subject: F.Y.I. AT Terminal
Date: August 2, 1988
- - - - - - - - - - - - - - - - - -
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!! NOTE: This problem has been fixed in later releases !!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
GENERAL
INFORMATION: The AT terminal is supported as a diskless workstation that
has the capability of adding one or two floppies. Floppy
upgrade kits can be ordered to accommodate either one 5 1/4,
one 3 1/2 or two 3 1/2 inch floppy drives. All kits include
only low density drives; 360 KB for the 5 1/4 and 720 KB for
the 3 1/2 drives. To order the correct floppy kit, you will
need to know what kind of a machine the customer has.
There are three versions that the AT terminal can come in.
The first is identified by a metal front with a metal door
that can be closed over the floppy area. This machine is
sometimes referred to as a "SEED UNIT". Both the second and
third variations have plastic fronts with plastic doors but
have different motherboards. The second has a Samsung board
that has a fabrication number of 2123. It also has round
cylindrical part located at Y3 (see figure 1-1). This
machine is sometimes referred to as a "SAMSUNG UNIT". The
third version has a fabrication number of 2124 and has a
rectangular part located at Y3 (see figure 1-1). This
machine is sometimes referred to as a "SAMSEED UNIT". Please
note that the parts referred to are quite small and may be
a little difficult to locate.
---------
| |
| | Power
| | Supply # Denotes the location of the expansion bus
| #|
| # --------|
| xxx xxx| Location of floppy controller chips
| # x| Location of Y3
| # |
-------------------
Front of AT Terminal Figure 1-1
Should you encounter problems with a SEED UNIT (metal front
and door), please refer them to NHPD at (408)729-6700. These
are Beta evaluation units and need to be handled by NHPD.
Part numbers for AT Terminal floppy upgrade kits are as
follows:
SAMSUNG UNIT SEED UNIT SAMSEED UNIT
1 3 1/2 Floppy 720 KB 870-220001-100 870-220001-110 870-220001-111
2 3 1/2 Floppy 720 KB 870-220001-200 870-220001-220 870-220001-222
1 5 1/4 Floppy 360 KB 870-220001-300 870-220001-330 870-220001-333
3 1/2 upgrades must be purchased as a kit because they
include mounting hardware that isn't available separately.
5 1/4 kits include the chip set, AT type cable and the drive
and may, depending on the machine, include extra mounting
hardware.
If you feel you need to stick your neck out and quote a part
number to a customer, you had better be sure you have the
right one for the machine that they have. If you are not
sure, send them to the parts department.
AT TERMINAL BIOS DRIVE TABLE (ver 2.66)
Drive Type Heads Cylinders Precomp
1 4 306 128
2 4 615 300
3 6 615 300
4 8 940 512
5 6 940 512
6 4 615 65535
7 8 462 256
8 5 733 65535
9 15 900 65535
10 3 820 65535
11 5 855 65535
12 7 855 65535
13 8 306 128
14 7 733 65535
15 0 0 0
16 4 612 0
17 5 977 300
18 7 977 65535
19 7 1024 512
20 5 733 300
21 7 733 300
22 5 733 300
23 4 306 0
24 9 1024 65535
25 8 640 0
26 6 820 65535
27 9 1024 0
28 5 1024 1025
29 9 925 925
30 5 830 512
31 7 830 512
32 10 830 0
33 7 1185 576
34 8 1024 1024
35 10 823 823
36 4 752 752
37 8 615 615
38 6 872 650